close
close
Unimatic, Blind Bolt Fastener, High Strength, Pull-Type, Positive Mechanical Lock, Protruding Head, Large Footprint
Unit of Measure

Nominal Diameter

N/A 06

Design Grip Range Min. - Max.

N/A 0.531 - 0.595

A Head

N/A 0.389 in

B

N/A 0.080 in

C Min

N/A 0.875 in

D

N/A 0.198 in

E Max

N/A 0.320 in

J

N/A 0.375 in

K

N/A 0.830 in

N

N/A 0.160 in

R Rad Max

N/A 0.015 in

(S) Max Ref

N/A 0.292 in

W Min.

N/A 0.277 in

Single Shear Strength

N/A 2925 lb

Tensile Strength

N/A 1400 lb

Spindle Ret.

N/A 845.000 lb

Hole Size

N/A 0.199 in

Grip Dash No.

N/A 09

Overlap Grip Min

N/A 0.515 in

Overlap Grip Max

N/A 0.611 in

Design Grip Range Min.

N/A 0.531 in

Design Grip Range Max.

N/A 0.595 in

Finish Code

N/A None

Installed Weight

N/A 5.33 lb

Sleeve Material

N/A CP titanium per ASTM-B348

Pin Material

N/A 38-6-44 titanium per AMS4957

Lock Collar Material

N/A A-286 cres per AMS5737

Sleeve Finish

N/A None

Pin Finish

N/A None

Lock Collar Finish

N/A Passivate per AMS QQ-P-35 and AMS2700

Sleeve Lube

N/A None or cetyl alcohol per (chlorine free) per AS87132 Type1 or dry film lube per AS5272 at manufacture's option

Pin Lube

N/A None or cetyl alcohol (chlorine free) per AS87132 Type1 or dry film lube per AS5272 at menufacture's option

Lock Collar Lube

N/A None or lox compatible dry film lube at manufacturer's option

N/A 1. -05 dia size also available with reduced O.D. drive anvil of .312+.005 (see sheet 3).
2. Applies to grips 05-03 Max, 06-03 Max, 08-04 Max and greater. In shorter grips, a true composite shear test cannot be performed.
3. Trim flash not to exceed .005" maximum length above head of pin.
4. Solid or split lock collar at manufacturer´s option. Split not to exceed .020 width.
5. Knurled to retain fastener assembly. Not part of installed fastener.
6. Blind side head may be installed on 7° max slope.
7. Identification: Huck symbol, MV (for CP titanium sleeve material) and grip dash number.
8. Optional drive washer for installation with blunt tool. Not part of installed fastener.
9. Sleeve diameter "D" may be .002" undersized in this area.
10. Lube and lock collar material at manufacturer´s option.
11. Lubrication:
Serrated pin: None or cetyl alcohol (chlorine free) per AS87132 Type 1 or dry film lube per AS5272 at manufacturer´s option.
Machanical lock: None or lox compatible dry film lube at manufacturer´s option.
Sleeve: NO suffix and AC suffix: None or cetyl alcohol (chlorine free) per AS87132 Type 1 or dry film lube per AS5272 at manufacturer´s option.
12. DF suffix parts when lubed shall use AS5272 on any of the fastener components except mechanical lock may use lox compatible dry film lube (MFG´s option)