Dash Number (Grip) |
N/A 1700 |
Grip Range - Min. Grip |
N/A 1.650 in |
Grip Range - Max. Grip |
N/A 1.700 in |
Grip Range |
N/A 1.650-1.700 in |
A Dia Ref |
N/A 0.538 in |
B Dia Min |
N/A 0.494 in |
D Dia |
N/A 0.290 in |
E Dia Max |
N/A 0.290 in |
F Wrench Flats |
N/A 0.152 in |
G Ref |
N/A 0.065 in |
H Ref |
N/A 0.104 in |
L Max |
N/A 0.875 in |
R Rad |
N/A 0.030 in |
S Max |
N/A 0.020 in |
Minimum available grip length |
N/A -200 |
Recommended Hole Size |
N/A 0.290-0.293 |
J Dia Min |
N/A 0.450 in |
K Max |
N/A 0.500 in |
Break off Limits <5> |
N/A 0.000-0.103 |
Tensile Structural Failure (Min) |
N/A 2600 lb |
Double Shear Min |
N/A 9800 lb |
Locking Torque Min |
N/A 3.000 lb-in0.339 N-m |
V Gage Prot. |
N/A 0.044 in |
W Gage Dia |
N/A 0.432 in |
Material and Heat Treat |
N/A
Nut: 6AL-4V titanium per AMS4928 or AMS4967; heat treated per MIL-H-81200 to 95 ksi shear strength minimum. Maximum hydrogen content 125 ppm. Screw: A-286 per AMS 5731 or AMS 5734; heat treated to 175 ksi tensile min. Sleeve: 304 stainless steel per AMS 5639, heat treat as required for performance. Insert: Acetal per ASTM D4181. |
Finish |
N/A
(-) Nut: KAL-GARD ANN-RO #1012 conversion coating or phosphate flouride per AMS2486 may be used at manufacturer´s option. Sleeve & screw: Passivate per AMS-QQ-P-35, KAL-GARD ANN-RO #1013 conversion coating optional. Insert: None |
Lubricants |
N/A The following lubricants may be applied to any or all components in any combination as required for performance unless otherwise specified: Dry film lube per AS5272, TYPE I, everlube #812, parafin wax, or cetyl alcohol per MIL-L-87132. |
Applicable Specification |
N/A
Procurement specification: FCBF200 Special lube and finish: FCBF202 |
Material Type |
N/A Titanium |
Rated Shear Strength |
N/A 75 KSI |
Headstyle |
N/A 100° Flush |
Notes |
N/A
2. Locking feature consists of three (3) indentations located 120° apart on the periphery of the nut component and approximately .040° above intersection of the nut nose angle and O.D. 3. Composite blind fasteners with selected combinations of the above lubrications and finishes are specially coded and may be substituted for equivalent non-coded parts at manufactures option. Contact fairchild engineering. <4> Distortion shall not prevent insertion of the fastener into a ring gauge of length equal to one diameter and hole diameter equal to a minimum recommended hole. Insertion force shall not exceed 5.0 lbs. <5> An "L" in place of the dash (-) between the diameter dash number and the grip dash number designates modified break-off limits of +.053/.050. "EX: FCBF2012( )-6L200". |